1）C/L偏移：
1) C/L migration:
1、客戶圖紙上面焊盤部位長度沒有數據,數據測量時沒有進行管控;
1 and customer's drawing pad parts above length no data, data measured not control;
2、覆蓋膜開窗是切割機切割出來,切割窗口完成后需要進行二鉆定位孔,二鉆定位孔是切割出來,切割時定位孔容易出現撕裂或者不圓等現象,貼附時導致覆蓋膜定位孔對制品孔對不齊,導致開窗偏移,即出現C/L偏移.
2, covering membrane window is cutting machine cutting out after completion, cutting window need for two, two drill holes drilled positioning is cutting out, positioning hole during cutting positioning hole prone to rent or not round etc. Phenomenon, attached with a lead to coverage of membrane positioning hole to not neat, products hole that led to open the window migration, appear C/L migration.
2）短路：
2) short-circuit:
1. 打樣時因數量少作業員手工開料,由于基材薄,開料后產品有些折皺,導致曝光時出現曝光不良,DES后形成短路現象.
1. When less homework because of quantity salesman manual opens the material, because members backing thin, opens the material products, leading to expose some wrinkles appear after exposure bad, DES formed short-circuit phenomenon.
2.樣品打樣交期緊,當時測試治具沒有制作回來,所以敝司暫定要求FQC檢驗員在40X顯微鏡下對線路進行100%開短路檢驗,因檢查員不仔細未發現導致不良漏檢流出
2. Sample proofing delivery tight, then test fixture did not make back, so our company 40X provisionally requirements under microscope in FQC inspectors to open the lines, for 100% short-circuit test that causes not carefully inspectors, adverse undetection outflow
3. 流出原因：
3. Outflows reasons:
檢查員不仔細未發現導致不良漏檢流出.
Inspector without careful not found that lead to bad undetection outflow.
4. 發生對策 ：
4. Happen countermeasures:
1）C/L偏移：
1) C/L migration:
1.發現覆蓋膜開窗偏移大的產品需要測數確認,超出公差范圍的產品報廢處理；
1. Find indusium window offset big products need to test several confirmation, beyond the tolerances products rejected processing;
2.量產時開鋼模可以完全避免此現象發生.
2. When open mass production to completely avoid the steel mold phenomenon.
2)短路：
2) short-circuit:
1.對開料工序作出要求,樣品無論數量多少,都要使用機器開料,確?；钠秸?
1. Commuting requirements, material process make sample regardless of the quantity, want to use the machine to ensure open material base material smoothness.
2. 電測治具已經OK,量產時通過電測治具對開短路進行測試,可以徹底避免此不良流出；
2. Electrical measurement fixture has OK, mass production by electrical measurement when opening fixture short-circuit test, can completely avoid the bad outflow;
5.流出對策：
5. Outflows countermeasures:
1. 客訴不良對FQC檢驗員進行培訓,同時后續所有的樣品檢查FQC固定2人專門對應.
1. Poor aftersale inspectors to FQC trained, and subsequent all samples check FQC 2 special fixed position.